11.
|
Reinforced Concrete structures are designed to satisfy requirements regarding safety, serviceability and durability throughout their design service life. The present pape [...]
|
12.
|
The use of lime for the construction of buildings and monuments has a long tradition. Therefore, limebased materials are also predominantly used and often even required i [...]
|
13.
|
This article is focused on the computational solution of the material tests and their evaluations. Problem deals with torsion low-cycle fatigue tests of steel specimens. [...]
|
14.
|
Abdominal aortic aneurysm is usually manifested like balloon dilation of the distal aorta. This bulge is probably caused by degradation processes in an arterial wall. Sha [...]
|
15.
|
The aim of this paper is to investigate the beginnings of crack propagation from sharp V-notches. Stress distribution around the tip of a V-notch is described on the basi [...]
|
16.
|
Pečínka, L.
Pipe break probabilities calculated in nuclear industry for purposes of PSA studies are based either on the in sights from the operating experience or on the fracture mec [...]
|
17.
|
Specific feature of the nuclear power plants is in comparison with coal fired plants the break postulation of each high energy piping. Fluid system is considered as high- [...]
|
18.
| |
19.
| |
20.
|
Historic urban areas are losing their traditional functions and are known for facing pressures by change agents such as tourism. Rapid urban development has proven to neg [...]
|
21.
|
This article deals with the parameters and governing mechanisms of the early water transport between mortar and brick. Two bricks with different transport parameters were [...]
|
22.
| |
23.
|
The concept of $J_R$ curves is well established in structure assessment. However, the shape of $J_R$ curves is influenced by constraint e ects significantly. Such phenome [...]
|
24.
|
Losík, V.
So far the static as well as dynamic aeroelastic tasks have been commonly solved by using linear models of fluid flow (p-k method, DLM) implemented e.g. in system MSC.Nas [...]
|
25.
|
Corrosion of reinforcing steel in concrete is one of the most influencing factors causing the degradation of reinforced concrete structures, conducting to concrete crack [...]
|
26.
| |
27.
|
Paper is focused on comprehensive solution of probabilistic integrity assessment of pressure vessels. Engineering criteria was fully respected during solution, however fr [...]
|
28.
|
Seven ductile fracture criteria are applied to simulation of cold forward extrusion and their performance in prediction of chevron cracks is presented. The criteria are i [...]
|
29.
|
This report documents the first part of research supported by the grant of Ministry of Industry and Trade of Czech Republic. The holder of grant is Aeronautical Research [...]
|
30.
|
This article shows: 1. Some studies of a low-cycle material fatigue caused by cyclical contact between two spheres with the same diameters. The spheres are made up from m [...]
|
31.
|
This paper presents a simulation of 3D curved crack propagation in a steam turbine blade lock. These fatigue cracks are often initiated near a blade root contact zone. Tw [...]
|
32.
|
The calibration of the potential method DC/PD is calculated for the side-grooved CT-sample with point current inputs. The grooves are modelled by a line transition resist [...]
|
33.
|
Maleček, J.
The work described in this contribution was performed as a part of the 3AS project (Active Aeroelastic Aircraft Structures) which is funded under contract (Contract No. G [...]
|
34.
| |
35.
|
The presented paper documents the concept and some major results of the heat transfer and stress analyses performed on a cylinder and a cylinder head of an aircraft pisto [...]
|
36.
| |
37.
|
Presented paper deals with computational fatigue strength prediction of high pressure level steam turbine blade pin joints. Quazi-static FE analysis of one turbine disk s [...]
|
38.
|
A 3D elastic-plastic FEM model with small strains was used for simulation of the deformation mechanics at the curved front of the planar fatigue crack growing in the thic [...]
|
39.
|
A two-parameter fracture mechanics method is applied to small cracks near a stress concentrator. The small crack in the present contribution is considered as crack influe [...]
|
40.
|
This contribution presents a simple numerical model for crack growth under mode-I compressive fatigue loading. Residual tensile stress at the crack tip, which is responsi [...]
|
41.
|
Structures operating at high temperatures are damaged by creep processes. If the structure is also subjected to cyclic loading, the fatigue damage is usually significant. [...]
|
42.
|
The fatigue crack growth rate in the Eurofer 97 steel was measured by two different methodologies. Small crack growth data were obtained using cylindrical specimens with [...]
|
43.
|
Čečrdle, J.
The paper deals with the aircraft landing shock aeroelastic response analysis. The analysis was performed as a part of the aircraft certification in order to fulfill the [...]
|
44.
|
To the interpretation of crack growth, it is substantial to estimate the plastic region geometry in front of a crack. Performed here is a study for predicting crack growt [...]
|
45.
|
The article is a contribution to numerical simulations of pitting arise phenomena on the gear teeth. The basic assumption of the presented simulations was that pitting (p [...]
|
46.
|
The crack growth prediction techniques in the critical area of the small transport aircraft undercarriage bracket has been describe in this paper. Stress-state was determ [...]
|
guest ::