1.
|
Historic urban areas have become major tourist attractions. It is known that tourism can affect them both positive and negatively, but defining its real impact on local c [...]
|
2.
|
Jeebori, A.
Tube banks are widely used in crossflow heat exchangers. Usually, the methods for its design are the NTU or LMTD methods, while in this research the Entropy Generation Me [...]
|
3.
|
Ductile fracture criteria are used for fracture prediction in metal forming processes. In this paper, there is briefly described the method of criteria verification and t [...]
|
4.
|
This paper is aimed at the problem of limit load carrying capacity of pipeline damaged by surface corrosion defects. Burst (limit) pressure is predicted using methodology [...]
|
5.
|
Abdominal aortic aneurysm is usually manifested like balloon dilation of the distal aorta. This bulge is probably caused by degradation processes in an arterial wall. Sha [...]
|
6.
|
The paper is devoted to fatigue crack propagation in layered materials. The influence of plasticity induced crack closure on threshold values for fatigue crack propagatio [...]
|
7.
|
The following article presents the results of analysis of slender bridge structure to dynamic loads induced by movement of people. Further is emphasized the importance of [...]
|
8.
|
Pohl, K.
The objective of this paper describe a non-linear analysis of reinforced concrete frame structures and assignment its response to seismic load. We observe the change of n [...]
|
9.
|
Špetl, J.
The paper deals with the actual problem in the field of dependability - the economics aspects of reliability testing. The paper points on input costs analysis connected w [...]
|
10.
|
The influence of corner singularity on crack behaviour for a threedimensional structure is described in this paper. The distribution of stress singularity through the thi [...]
|
11.
|
The aim of this paper is to investigate the beginnings of crack propagation from sharp V-notches. Stress distribution around the tip of a V-notch is described on the basi [...]
|
12.
|
This paper presents a simulation of 3D curved crack propagation in a steam turbine blade lock. These fatigue cracks are often initiated near a blade root contact zone. Tw [...]
|
13.
|
This contribution deals with reliability of railway wheels as influenced by the occurrence of impaired limiting material strength. Results are presented of material inves [...]
|
14.
| |
15.
|
Kriváček, J.
The plates of thin-walled steel structures to be in nature imperfect may exhibit out-of-plane displacements (deflections) under in-plane compressive load. Such type of st [...]
|
16.
|
The calibration of the potential method DC/PD is calculated for the side-grooved CT-sample with point current inputs. The grooves are modelled by a line transition resist [...]
|
17.
|
In this paper is solved a 3D analysis of growing crack of the chevron notched three-point-bending specimen. On macroscale the specimen body is modeled as an elastic homog [...]
|
18.
|
A 3D elastic-plastic FEM model with small strains was used for simulation of the deformation mechanics at the curved front of the planar fatigue crack growing in the thic [...]
|
19.
|
The contribution deals with the 3D analysis of the chevron notched three point bending specimen which is used to determine the fracture toughness of brittle matrix compos [...]
|
20.
|
A substantial number of experimentally based works indicate the changes in crack propagation direction on bi-material interface in composite laminate materials. The paper [...]
|
21.
|
The contribution discusses possible approach for the formulation of fracture criteria for the general stress concentrators – especially a surface crack terminating at t [...]
|
22.
|
The fatigue crack growth rate in the Eurofer 97 steel was measured by two different methodologies. Small crack growth data were obtained using cylindrical specimens with [...]
|
23.
|
The concept of $J_R$ curves is well established in structure assessment. However, the shape of $J_R$ curves is influenced by constraint e ects significantly. Such phenome [...]
|
24.
|
Paper is focused on comprehensive solution of probabilistic integrity assessment of pressure vessels. Engineering criteria was fully respected during solution, however fr [...]
|
25.
|
A two-parameter fracture mechanics method is applied to small cracks near a stress concentrator. The small crack in the present contribution is considered as crack influe [...]
|
26.
|
Seven ductile fracture criteria are applied to simulation of cold forward extrusion and their performance in prediction of chevron cracks is presented. The criteria are i [...]
|
27.
|
Structures operating at high temperatures are damaged by creep processes. If the structure is also subjected to cyclic loading, the fatigue damage is usually significant. [...]
|
28.
|
The stability criteria of V-notched bodies under combination of loading modes I and II are suggested and compared in the article. Methodology of stability criterion sugge [...]
|
29.
|
The crack growth prediction techniques in the critical area of the small transport aircraft undercarriage bracket has been describe in this paper. Stress-state was determ [...]
|
30.
|
The article is a contribution to numerical simulations of pitting arise phenomena on the gear teeth. The basic assumption of the presented simulations was that pitting (p [...]
|
31.
|
This contribution presents a simple numerical model for crack growth under mode-I compressive fatigue loading. Residual tensile stress at the crack tip, which is responsi [...]
|
32.
|
To the interpretation of crack growth, it is substantial to estimate the plastic region geometry in front of a crack. Performed here is a study for predicting crack growt [...]
|